View OBP02170_4544835.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MEDICAL & MILITARY
Medline 300 Series
2 0 0 - 3 0 0 W AT T S S I N G L E & M U LT I P L E O U T P U T A C / D C M E D I C A L
Features
* EN61000-3-2 class A and D compliant. * Power factor 0.98 typical. * Remote sense on output 1 and output 2. * Overvoltage protection. * Overcurrent protection. * Power fail detection (PFD) signal. * 100% burn-in at full rated load. * Remote inhibit - TTL high disables output. * Short curcuit protection
Specifications
INPUT
Input Voltage Frequency Input Current Leakage current Isolation 90-264Vac 47Hz-63Hz 4.7A (rms) for 115Vac 2.2A (rms) for 230Vac 90A max. at 115Vac. 60Hz 150A max. at 230Vac. 50Hz Input - Output: 4000VAC Input - Ground: 1500VAC Output - Ground: 500VAC 30A at 115V or 80A at 230V at 25C and cold start
OPERATING
MTBF Efficiency 350,000 hrs @ 25C 70% minimum.
ENVIRONMENTAL
Operating Temperature Derating Storage Temperature Humidity Cooling 0C to 70C Derate from 100% at +50C linearly to 50% at 70C -40C to 85C 5%-95% non-condensing 35 CFM forced air, provided on "C" version, to be provided for "B" version by user
Inrush Current
OUTPUT
Power Voltage Ripple & Noise Overvoltage Protection Overcurrent Protection Temperature Coefficient Transient Response See table See table 2% peak to peak max Provided on output #1 only. Set at 115%-140% of nominal output voltage All outputs protected for short circuit conditions All outputs 0.04% per C Max. excursion of 4%or better on all models, recovering to 1% of final value within 500s after a 25% step load change TTL logic high for normal operation and TTL logic low upon loss of input power. This signal appears at least 1ms prior to +5V output dropping 5% below its nominal value. This signal also provides a minimum delay of 100ms after +5V is within regulation Requires an external TTL high level signal to inhibit outputs for standard models 0.2% maximum at full load Typically 12ms at 110VAC
STANDARDS AND APPROVALS
Safety standards C-Tick EMC standards UL60601-1, TUV EN60601-1 AS/NZS CISPR11 Group 1, Class A EN55011 Class B, FCC Class B, EN61000-3-2, -3, EN61000-4-2, -3, -4, -5, -6, -8, -11
MECHANICAL
Dimensions Weight 177.8x101.6x38.1mm 0.82Kgs for "B" version. 0.96Kgs for "C" version.
PFD Signal
Remote inhibit Line Regulation Holdup Time
Your dependable power partner - www.powerbox.com.au
347
MEDICAL & MILITARY
Medline 300 Series
2 0 0 - 3 0 0 W AT T S S I N G L E & M U LT I P L E O U T P U T A C / D C M E D I C A L
Selection Table
MAX. MODEL NUMBER VNOM OUTPUT #1 IMIN IMAX TOL OUTPUT #2 VNOM IMIN IMAX TOL VNOM OUTPUT #3 IMIN IMAX TOL VNOM OUTPUT #4 IMIN IMAX TOL OUTPUT POWER
OBP02013 OBP02016 OBP02031 OBP02037 OBP02046 OBP02055 OBP02170 OBP02403 OBP02404 OBP02407 OBP02410 OBP02413 OBP02418 OBP02419 OBP02424 OBP02427 OBP02430 OBP02433 OBP02436 OBP02439 OBP02442
3.3V 5.1V 12V 15V 24V 30V 48V +3.3V +5.1V +5.1V +5.1V +5.1V +5.1V +5.1V +5.1V +5.1V 24V 24V 24V 24V 24V
0A 0A 0A 0A 0A 0A 0A 3.0A 2.0A 2.0A 2.0A 2.0A 2.0A 2.0A 2.0A 2.0A 0.5A 0.5A 0.5A 0.5A 0.5A
60A 60A 25A 20A 12.5A 10A 6.3A 35A 35A 35A 35A 35A 35A 35A 35A 35A 6.3A 6.3A 6.3A 6.3A 6.3A
3% 2% 2% 2% 2% 2% 2% 3% 2% 2% 2% 2% 2% 3% 2% 2% 2% 2% 2% 3% 2% 5.1V 12V 15V 12V 12V 12V 24V 24V 12V 12V 12V 12V 24V 24V 2.0A 1.0A 0.8A 1.0A 1.0A 1.0A 0.5A 0.5A 1.0A 1.0A 1.0A 1.0A 0.5A 0.5A 22A 10A 8A 10A 10A 10A 5A 5A 10A 10A 10A 10A 5A 5A 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 2% 12V 12V 15V 12V 12V 12V 12V 5.1V 5.1V 5.1V 5.1V 12V 5.1V 12V 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 4A 4A 4A 4A 4A 4A 4A 4A 4A 4A 4A 4A 4A 4A 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 12V 5.1V 24V 12V 24V 15V 12V 15V 24V 12V 24V 12V 15V 12V 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 4A 4A 2.5A 4A 2.5A 4A 4A 4A 2.5A 4A 2.5A 4A 4A 4A 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 4%
200W 300W 300W 300W 300W 300W 300W 250W 300W 300W 300W 300W 300W 300W 300W 300W 300W 300W 300W 300W 300W
NOTES: (1) Add suffix "B" for U-bracket format and "C" for enclosed format. (2) All outputs are floating. It can be connected externally for postive or negative output. (3) Output 1 and 2 can be adjusted within 5% of their nominal voltage. (4) Output 3 and 4 can be adjusted within 15% of their nominal voltage. (5) 300 watts for "C" version with a cover and fan assembly 150 watts for "B" version without moving air (maximum current of ouput #1 & #2 derated to 50%), or 300 watts with 25 CFM forced air provided by user. (6) PM300-10-3 is rated 200 watts with 35 CFM forced air cooling or 100 watts convectional cooled. PM300-40-3 is rated 250 watts with 35 CFM forced air cooling (maximum current of output 1 & 2 derated to 50%) or 125 watts convection cooled. (7) Single output models may be operated at no-load. At no-load, output voltage tolerance increases to 10%.
Pin Connection
CONNECTOR P1(AC) MODEL/PIN
OBP02013 OBP02031 OBP02046 OBP02070 OBP02016 OBP02037 OBP02055
P2
P3
P4
P5
P6
1
Live
2
Neutral
3
Ground OUTPUT OUTPUT #1 OUTPUT #1 OUTPUT #1 OUTPUT #1 #1 RET
CONNECTOR P4 MODEL/PIN
OBP02013 OBP02031 OBP02046 OBP02070 OBP02016 OBP02037 OBP02055
1
SIGNAL GROUND
2
+S (Vo1)
3
-S (Vo1)
4
PFD
5
INHIBIT
6
N.C.
7
N.C.
8
N.C.
9
OV (FAN)
10
12V (FAN)
348
MEDICAL & MILITARY
Medline 300 Series
2 0 0 - 3 0 0 W AT T S S I N G L E & M U LT I P L E O U T P U T A C / D C M E D I C A L
Pin Connection ctnd
P1(AC) MODEL/PIN
OBP02403 OBP02407 OBP02413 OBP02419 OBP02427 OBP02433 OBP02439 OBP02404 OBP02410 OBP02418 OBP02424 OBP02430 OBP02436 OBP02442
P2 3
P3
P5
P6
P7 1 2 3 4
1
2
Live
Neutral
Ground
OUTPUT #1
OUTPUT #1 RET
OUTPUT #2
OUTPUT #2 RET
OUTPUT #3
OUTPUT #3 RET
OUTPUT #4
OUTPUT #4 RET
CONNECTOR P4 MODEL/PIN
OBP02403 OBP02407 OBP02413 OBP02419 OBP02427 OBP02433 OBP02439 OBP02404 OBP02410 OBP02418 OBP02424 OBP02430 OBP02436 OBP02442
1
2
3
4
5
6
7
8
9
10
SIGNAL GROUND
+S (Vo1)
-S (Vo1)
PFD
INHIBIT
N.C.
N.C.
N.C.
OV (FAN)
12V (FAN)
Technical Illustration
SINGLE
Note: 1. Dimensions shown in inches (mm) 2. Tolerance 0.02 (0.5) maximum Input connector P1 is DT-35-B01W-03 screws are M3, Nickel plated 3. Connector P4 mates with Molex housing 50-37-5103 and pins 5263 4. Connectors P2, P3, P5 and P6: M3*0.5 screw connections 5. 12V (P4) is for DC fan rated 12V/0.1A 6. Weight 1.20 Kgs approx
MULTIPLE
Note: 1. Dimensions shown in inches (mm) 2. Tolerance 0.02 (0.5) maximum 3. Input connector P1 Dinkle is DT-35-B01W-03 screws are M3, Nickel plated 4. Connector P4 mates with Molex housing 50-37-5103 and pins 5263 5. Connectors P2, P3, P5 and P6: M3*0.5 screw connections 6. Output connector P7 mates Molex housing 09-50-3041 and Molex 2878 series crimp terminal 7. 12V (P4) is for DC fan rated 12V/0.1A 8. Weight 1.20 Kgs approx
Your dependable power partner - www.powerbox.com.au
349

▲Up To Search▲

Price & Availability of OBP02170

	To Download OBP02170 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .